Every heat of steel comes with a mill test report: the chemistry and mechanical properties that show the material meets its specification. For decades that report traveled as paper, then as a PDF attached to an email. More customers now want it as data, through the EDI 863 report of test results, so their quality systems can check it automatically instead of someone reading a PDF.
This article explains what the 863 carries, how it connects to the shipment, and why it is usually harder for a service center than for a mill.
What a mill test report proves
A mill test report, or MTR, ties one heat number to the results of the tests run on it. A typical report includes:
- The heat number, the grade, and the specification the material is certified to
- Chemical composition by element, such as carbon, manganese, phosphorus, sulfur, and silicon
- Mechanical properties such as yield strength, tensile strength, and elongation
- Any additional results the order calls for, such as hardness or coating weight
The customer compares those numbers with what it ordered. If a value is out of range, the material should not go into production.
Why customers move certs to EDI
A PDF has to be opened, read, and keyed into a quality system, often after the steel is already on the floor. An 863 arrives as structured data. The customer’s system can compare each value with the spec on receipt and flag a problem before anyone touches the coil. For a buyer receiving many heats a week, that is the difference between checking every cert and checking a sample.
It also completes the traceability record. The heat number on the 863 matches the heat number on the 856 ship notice, so the customer can link every tag it receives to the test results for that heat.
What goes into an 863
The 863 identifies the heat and product being reported, then lists each test result as a measurement with its value, its unit of measure, and the test or element it applies to. Customers usually specify which elements and properties they require, which units to use, and whether results must be reported against minimum and maximum limits.
As with every EDI document, the implementation guide controls the details. Two customers can ask for the same results in different units or with different qualifiers, and the map has to handle both.
Common problems
The results are not in the ERP. Lab data often lives in a separate laboratory or quality system, or only on the PDF the mill sent. The EDI map can only send data it can read, so the first job is finding where the numbers are actually stored.
Units do not match. Strength in ksi versus MPa, or chemistry as a percentage versus parts per million. A wrong unit can make a good heat look out of spec, or the reverse.
Different grades report different elements. A map built around one grade can miss elements another grade requires. The map needs to follow the grade, not a fixed list.
Timing. If the 863 arrives days after the material, the customer either holds the shipment or receives it unverified. It should go out at or before shipment.
The service center problem: passing certs through
Mills generate their own test results. Service centers and processors usually do not. They receive coils with the mill’s cert, process them into new pieces, and then owe their own customer a cert for each piece they ship.
That means carrying the mill’s results forward through slitting, cutting, and re-tagging, so every child piece still points to the original heat and its results. When the mill sends its certs by EDI, the service center can relay that data downstream instead of retyping it. When the mill sends PDFs, someone has to extract the values first, or the customer gets a PDF when it asked for data.
Processing can add tests of its own, such as flatness or dimensional checks. Those belong on the outbound cert too, alongside the mill’s original results.
Getting started
- Collect the customer’s 863 implementation guide, and a sample file if they have one.
- Find where test results live today for each source: your own lab, mill EDI, or mill PDFs.
- Confirm the heat number follows every tag through processing, so certs and ship notices agree.
- Agree on units and on which elements each grade requires.
Foundational manages 863 test results alongside the 856, the 810, and the rest of the metals document set for mills, service centers, and processors. See the full list on our steel processing page, and the Nucor case study for what that looks like at scale. If a customer has asked you for certs by EDI, send us the spec and we will map out what your systems need to provide.
Ready to simplify your EDI operations?
Talk to a specialist about your trading partners, ERP, and current EDI setup. Talk to a Specialist